This is the first question on almost every call, and it's a fair one to ask up front. The honest range we can give you before seeing the space is roughly $15 to $40-plus per square foot, and that spread is wide on purpose — microcement pricing depends on what's actually happening under your existing floor or wall, not just the square footage. Anyone who quotes you a flat number sight unseen is guessing, and we'd rather walk your space and give you a number we can stand behind.
Why the Range Is So Wide
A $15/sqft job and a $40/sqft job can both be legitimate microcement installs — they're just different jobs. A small powder room floor over sound, level concrete with a single neutral color is a straightforward scope. A full kitchen that includes floors, an island, and a backsplash, over a substrate with cracks and old adhesive residue, in three coordinated tones, is a different amount of labor and material entirely. The material itself is a relatively small part of the total cost on most jobs — labor, prep, and the number of coats are what actually move the number.
Substrate Condition Is the Biggest Swing Factor
Before we quote anything, we check what's under the surface — tile, concrete, wood subfloor, old vinyl. Sound, level, well-bonded substrates keep the prep stage short: clean, key the surface, prime, and move on to base coats. But if there's cracking, delamination, an uneven transition between rooms, or old flooring that needs grinding down first, that prep work adds real hours before a single coat of microcement goes on. We flag this during the consultation, not after we've started, because substrate issues are the single most common reason a quote comes in higher than someone expected.
Square Footage and Scope
Bigger jobs generally bring the per-square-foot number down slightly, since setup, material staging, and travel get spread across more area — but this only goes so far, and a large floor with a complicated layout can still run higher than a small, simple one. What matters more than raw square footage is scope: are we doing just the floor, or the floor plus walls plus a shower pan? Every additional surface is its own prep-apply-seal cycle, even if it's in the same room.
Number of Coats and Colors
Our standard installs run two to three thin coats, each about 2 to 3mm combined, hand-troweled and cured between applications. A single consistent color across a space is the most efficient path. Multiple colors in one room, a color transition between zones, or a decorative technique like a two-tone wall all add coordination time and often an extra coat where colors meet, which shows up in the price.
Indoor vs. Outdoor and Wall vs. Floor vs. Countertop
Outdoor work — pool decks, patios, driveways — generally costs more per square foot than an equivalent indoor floor, mainly because of UV-stable sealers, anti-slip additives, and the fact that outdoor substrates in Southern California often need more crack repair and expansion joint work before coating. Countertops sit at the higher end of the range too, since they're detail-heavy, need precise edge work, and get a heavier-duty sealer given constant contact with food, knives, and hot pans. Walls typically run a bit less than floors and countertops for the same square footage, since they take less foot-traffic wear and can sometimes go with fewer coats depending on the room.
Site Access and Logistics
A ground-floor room with easy material access is simpler to work than a third-floor condo unit with a narrow elevator, or a job where we're protecting finished adjacent rooms and furniture that isn't moving out. Occupied homes, tight parking, HOA restrictions on work hours, and multi-story access all add time that isn't about the microcement itself but still shows up in the labor line of a quote.
Why Supplier-and-Installer Pricing Looks Different
We supply the microcement material ourselves and install it with our own crew, rather than subcontracting the labor or marking up material bought from a separate distributor. That structure tends to keep pricing tighter than jobs where a general contractor is coordinating between a material supplier and a separate installation crew, since there's no middleman margin stacked on top of either side. It also means the person quoting your job understands exactly what the material can and can't do on your specific substrate, instead of relaying assumptions from a supplier who's never seen the property.
Comparing Microcement Pricing to Tile or Natural Stone
Clients sometimes come in comparing a microcement quote directly to a tile estimate and are surprised the ranges don't line up cleanly. Tile pricing is more standardized because the material itself is a fixed unit cost, and installation follows a fairly predictable pattern regardless of who's doing it. Microcement is closer to a custom finish — it's applied by hand in multiple thin layers, tinted and blended on site, and the labor-to-material ratio runs higher than it does for tile. For a comparable square footage, mid-range natural stone or large-format porcelain tile can land in a similar range to microcement, particularly once you factor in grout work, edge trim, and transition pieces that microcement's seamless application avoids entirely.
What a Real Quote Looks Like
We don't price jobs over the phone past a rough range, and we'd be skeptical of any contractor who does. A real quote comes from an in-person walkthrough where we check the substrate, measure the actual area, talk through color and coat count, and account for the access situation at your property. That's the number we put in writing, and it's the number that holds once we start work — no surprise change orders because someone guessed low to win the job.
Want a number specific to your space? Get a free walkthrough and a written quote based on what we actually see.
Get a Free Quote